Search results

This paper presents the experimental and numerical results of the bending properties of low-height prestressed T-beams. The purpose is to study the bearing capacity, failure state and strain distribution of low-height prestressed T-beams.

First, two 13 m-long full-size test beams were fabricated with different positions of prestressed steel bundles in the span. The load–deflection curves and failure patterns of each test beam were obtained through static load tests. Secondly, the test data were used to validate the finite element model developed to simulate the flexural behavior of low-height prestressed T-beams. Finally, the influence of different parameters (the number of prestressed steel bundles, initial prestress and concrete strength grade) on the flexural performance of the test beams is studied by using a finite element model.

The test results show that when the distance of the prestressed steel beam from the bottom height of the test beam increases from 40 to 120 mm, the cracking load of the test beam decreases from 550.00 to 450.00 kN, reducing by 18.18%, and the ultimate load decreases from 1338.15 to 1227.66 kN, reducing by 8.26%, therefore, the increase of the height of the prestressed steel beam reduces the bearing capacity of the test beam. The numerical simulation results show that when the number of steel bundles increases from 2 to 9, the cracking load increases by 183.60%, the yield load increases by 117.71% and the ultimate load increases by 132.95%. Therefore, the increase in the number of prestressed steel bundles can increase the cracking load, yield load and ultimate load of the test beam. When the initial prestress is from 695 to 1,395 MPa, the cracking load increases by 69.20%, the yield load of the bottom reinforcement increases by 31.61% and the ultimate load increases by 3.97%. Therefore, increasing the initial prestress can increase the cracking load and yield load of the test beam, but it has little effect on the ultimate load. The strength grade of concrete increases from C30 to C80, the cracking load is about 455.00 kN, the yield load is about 850.00 kN and the ultimate load is increased by 4.90%. Therefore, the improvement in concrete strength grade has little influence on the bearing capacity of the test beam.

Based on the experimental study, the bearing capacity of low-height prestressed T-beams with different prestressed steel beam heights is calculated by finite element simulation, and the influence of different parameters on the bearing capacity is discussed. This method not only ensures the accuracy of bearing capacity assessment, but also does not require a large number of samples and has a certain economy. The study of prestressed low-height T-beams is of great significance for understanding the principle and application of prestressed technology. Research on the mechanical behavior and performance of low-height prestressed T beams can provide a scientific basis and technical support for the design and construction of prestressed concrete structures. In addition, the study of prestressed low-height T-beams can also provide a reference for the optimization design and construction of other structural types.

As an important load-bearing component of cable-stayed bridge, the cable-stayed cable is an important load-bearing link for the bridge superstructure and the load transferred directly to the bridge tower. In order to better manage the risk of the cable system in the construction process, the purpose of this paper is to study a new method of dynamic risk analysis of the cable system of the suspended multi-tower cable-stayed bridge based on the Bayesian network.

First of all, this paper focuses on the whole process of the construction of the cable system, analyzes the construction characteristics of each process, identifies the safety risk factors in the construction process of the cable system, and determines the causal relationship between the risk factors. Secondly, the prior probability distribution of risk factors is determined by the expert investigation method, and the risk matrix method is used to evaluate the safety risk of cable failure quantitatively. The function expression of risk matrix is established by combining the probability of risk event occurrence and loss level. After that, the topology structure of Bayesian network is established, risk factors and probability parameters are incorporated into the network and then the Bayesian principle is applied to update the posterior probability of risk events according to the new information in the construction process. Finally, the construction reliability evaluation of PAIRA bridge main bridge cable system in Bangladesh is taken as an example to verify the effectiveness and accuracy of the new method.

The feasibility of using Bayesian network to dynamically assess the safety risk of PAIRA bridge in Bangladesh is verified by the construction reliability evaluation of the main bridge cable system. The research results show that the probability of the accident resulting from the insufficient safety of the cable components of the main bridge of PAIRA bridge is 0.02, which belongs to a very small range. According to the analysis of the risk grade matrix, the risk grade is Ⅱ, which belongs to the acceptable risk range. In addition, according to the reverse reasoning of the Bayesian model, when the serious failure of the cable system is certain to occur, the node with the greatest impact is B3 (cable break) and its probability of occurrence is 82%, that is, cable break is an important reason for the serious failure of the cable system. The factor that has the greatest influence on B3 node is C6 (cable quality), and its probability is 34%, that is, cable quality is not satisfied is the main reason for cable fracture. In the same way, it can be obtained that the D9 (steel wire fracture inside the cable) event of the next level is the biggest incentive of C6 event, its occurrence probability is 32% and E7 (steel strand strength is not up to standard) event is the biggest incentive of D9 event, its occurrence probability is 13%. At the same time, the sensitivity analysis also confirmed that B3, C6, D9 and E7 risk factors were the main causes of risk occurrence.

This paper proposes a Bayesian network-based construction reliability assessment method for cable-stayed bridge cable system. The core purpose of this method is to achieve comprehensive and accurate management and control of the risks in the construction process of the cable system, so as to improve the service life of the cable while strengthening the overall reliability of the structure. Compared with the existing evaluation methods, the proposed method has higher reliability and accuracy. This method can effectively assess the risk of the cable system in the construction process, and is innovative in the field of risk assessment of the cable system of cable-stayed bridge construction, enriching the scientific research achievements in this field, and providing strong support for the construction risk control of the cable system of cable-stayed bridge.

Effectively solving the large tonnage cable in the construction process due to the tensioning method of the inclined cable often appears in the overall cable force and the design value of the deviation is large, cable internal strand force is not uniform, the main girder stress exceeds the limit of the problem affecting the safety of the structure.

In this study, the finite element method and theoretical analysis method are utilized to propose a construction control method of tensioning the whole bunch of diagonal cables in two parts according to the deformation coordination relationship between the main girder and the diagonal cables. This methodology was implemented during the actual construction of the PAIRA Bridge in Bangladesh.

Tests conducted on cable-stayed bridges using this controlled tensioning method demonstrate that the measured cable strength of a single strand exhibits an error of less than 0.15% compared to the design target cable strength. The deviation between the measured and designed cable forces ranges from 0.16% to 0.27%. Furthermore, no tensile stress is observed in both the top plate and bottom plate of the root section of the main girder, indicating a state of full-section compression throughout the entire construction process.

Through the comparison with the test value, it can be proved that the whole bunch of diagonal cable tensioned in two parts of the construction control method proposed in this paper can make the internal strand force more uniform, to meet the precision requirements of the site construction, to protect the safety of the bridge construction process. The method proposed in this paper is highly accurate, easy to calculate, and has a high value of popularization and application.

When the reinforced concrete beams are reinforced by bonding steel plates to the bottom, excessive use of steel plates will make the reinforced concrete beams become super-reinforced beams, and there are security risks in the actual use of super-reinforced beams. In order to avoid the occurrence of this situation, the purpose of this paper is to study the calculation method of the maximum number of bonded steel plates to reinforce reinforced concrete beams.

First of all, when establishing the limit failure state of the reinforced member, this paper comprehensively considers the role of the tensile steel bar and steel plate and takes the load effect before reinforcement as the negative contribution of the maximum number of bonded steel plates that can be used for reinforcement. Through the definition of the equivalent tensile strength, equivalent elastic modulus and equivalent yield strain of the tensile steel bar and steel plate, a method to determine the relative limit compression zone height of the reinforced member is obtained. Second, based on the maximum ratio of (reinforcement + steel plate), the relative limit compression zone height and the equivalent tensile strength of the tensile steel bar and steel plate of the reinforced member, the calculation method of the maximum number of bonded steel plates is derived. Then, the static load test of the test beam is carried out and the corresponding numerical model is established, and the reliability of the numerical model is verified by comparison. Finally, the accuracy of the calculation method of the maximum number of bonded steel plates is proved by the numerical model.

The numerical simulation results show that when the steel plate width is 800 mm and the thickness is 1–4 mm, the reinforced concrete beam has a delayed yield platform when it reaches the limit state, and the failure mode conforms to the basic stress characteristics of the balanced-reinforced beam. When the steel plate thickness is 5–8 mm, the sudden failure occurs without obvious warning when the reinforced concrete beam reaches the limit state. The failure mode conforms to the basic mechanical characteristics of the super-reinforced beam failure, and the bending moment of the beam failure depends only on the compressive strength of the concrete. The results of the calculation and analysis show that the maximum number of bonded steel plates for reinforced concrete beams in this experiment is 3,487 mm². When the width of the steel plate is 800 mm, the maximum thickness of the steel plate can be 4.36 mm. That is, when the thickness of the steel plate, the reinforced concrete beam is still the balanced-reinforced beam. When the thickness of the steel plate, the reinforced concrete beam will become a super-reinforced beam after reinforcement. The calculation results are in good agreement with the numerical simulation results, which proves the accuracy of the calculation method.

This paper presents a method for calculating the maximum number of steel plates attached to the bottom of reinforced concrete beams. First, based on the experimental research, the failure mode of reinforced concrete beams with different number of steel plates is simulated by the numerical model, and then the result of the calculation method is compared with the result of the numerical simulation to ensure the accuracy of the calculation method of the maximum number of bonded steel plates. And the study does not require a large number of experimental samples, which has a certain economy. The research result can be used to control the number of steel plates in similar reinforcement designs.

The combination of an Engineered Cementitious Composite (ECC) layer and steel plate to reinforce RC beams (ESRB) is a new strengthening method. The ESRB was proposed based on the steel plate at the bottom of RC beams, aiming to solve the problem of over-reinforced RC beams and improve the bearing capacity of RC beams without affecting their ductility.

In this paper, the finite element model of ESRB was established by ABAQUS. The results were compared with the experimental results of ESRB in previous studies and the reliability of the finite element model was verified. On this basis, parameters such as the width of the steel plate, thickness of the ECC layer, damage degree of the original beam and cross-sectional area of longitudinal tensile rebar were analyzed by the verified finite element model. Based on the load–deflection curve of ESRB, ESRB was discussed in terms of ultimate bearing capacity and ductility.

The results demonstrate that when the width of the steel plate increases, the ultimate load of ESRB increases to 133.22 kN by 11.58% as well as the ductility index increases to 2.39. With the increase of the damage degree of the original beam, the ultimate load of ESRB decreases by 23.7%–91.09 kN and the ductility index decreases to 1.90. With the enhancement of the cross-sectional area of longitudinal tensile rebar, the ultimate bearing capacity of ESRB increases to 126.75 kN by 6.2% and the ductility index elevates to 2.30. Finally, a calculation model for predicting the flexural capacity of ESRB is proposed. The calculated results of the model are in line with the experimental results.

Based on the comparative analysis of the test results and numerical simulation results of 11 test beams, this investigation verified the accuracy and reliability of the finite element simulation from the aspects of load–deflection curve, characteristic load and failure mode. Furthermore, based on load–deflection curve, the effects of steel plate width, ECC layer thickness, damage degree of the original beam and cross-sectional area of longitudinal tensile rebar on the ultimate bearing capacity and ductility of ESRB were discussed. Finally, a simplified method was put forward to further verify the effectiveness of ESRB through analytical calculation.

Due to the deformation between the pylon and the girder caused by single tension of cables, the previously tensioned steel strands have stress relaxation, resulting in the actual cable forces being less than the design cable forces. To compensate the stress loss caused by the single tension of cables, this paper aims to present a practical compensation algorithm of stress relaxation during the construction period.

From the perspective of the essential cause of the stress relaxation, finite element analysis is used to solve the tension control force of each steel strand after a rigorous theoretical formula derivation.

The deformation and tension control force of each steel strand decrease with the advance of the tension sequence, and the decline rate drops gradually. However, the calculated force values of the steel strand are in good agreement with the measured value as the cable length decreases.

The previous rough calculation methods for the tension force of steel strands cannot meet the accuracy, and the accurate calculation methods often include the solution of nonlinear equations, which complicate the calculating process. Otherwise, there are few studies on the compensation of stress loss by calculating the deformation of the steel strand during the tension process. So, it developed an accurate and efficient algorithm to determine the tension control forces.

The application of ultra-high performance concrete (UHPC) in anchorage zones can significantly improve the local compression performance of structures. However, the high cost and complex preparation of UHPC make UHPC difficult to be widely used in practice. This study proposes a method to strengthen the local compression zone of structures built by normal strength concrete (NSC) by incorporating UHPC cores.

In this study, a Finite Element Model (FEM) of local compression specimens was established by ABAQUS, and the accuracy of FEM was verified by comparing the FEM calculation results with experimental results. The verified FEM was adapted to the research on the influences of affecting factors on local compression performance of structures, including NSC strength, UHPC strength, spiral steel bar strength, and UHPC core diameter.

The results show that the peak load of the strengthened specimen SC1-U + N increases by 210.2% compared to that of the SC1-NSC. Furthermore, compared to SC1, the strengthened specimen SC1-U + N can save 64.7% amount of UHPC while the peak load decreases by only 34.4%. The peak load of the strengthened specimens increases with the axial compressive strength and the diameter of UHPC cores increasing, crack load increases with increasing the compressive strength of NSC, the spiral steel bar with high strength can prevent the sharp drop of load-deflection curve and the residual bearing capacity increases accordingly. All findings indicate that increasing the diameter of UHPC cores can improve the overall performance of the specimens. Under loading, all specimens fail by following a similar pattern. The effectiveness of this new strengthen method is also verified by FEM analytical calculations.

Based on the experimental study, this study extrapolates the influence of different parameters on the local bearing capacity of the strengthened specimens by finite element simulation. This method not only ensures the accuracy of bearing capacity assessment, but also does not require many samples, which ensures the economy of the reinforcement process. The research results provide a reference for the reinforcement design of anchorage zone.

The flexural reinforcement of bridges in-service has been an important research field for a long time. Anchoring steel plate at the bottom of beam is a simple and effective method to improve its bearing capacity. The purpose of this paper is to explore the influence of anchoring steel plates of different thicknesses on the bearing capacity of hollow slab beam and to judge its working status.

First, static load experiments are carried out on two in-service RC hollow slab beams; meanwhile, nonlinear finite element models are built to study the bearing capacity of them. The nonlinear material and shear slip effect of studs are considered in the models. Second, the finite element models are verified, and the numerical simulation results are in good agreement with the experimental results. Finally, the finite element models are adopted to carry out the research on the influence of different steel plate thicknesses on the flexural bearing capacity and ductility.

When steel plates of different thicknesses are adopted to reinforce RC hollow slab beams, the bearing capacity increases with the increase of the steel plate thickness in a certain range. But when the steel plate thickness reaches a certain level, bearing capacity is no longer influenced. The displacement ductility coefficient decreases with the increase of steel plate thickness.

Based on experimental study, this paper makes an extrapolation analysis of the bearing capacity of hollow slab beams reinforced with steel plates of different thicknesses through finite element simulation and discusses the influence on ductility. This method not only ensures the accuracy of bearing capacity evaluation but also does not need many samples, which is economical to a certain extent. The research results provide a basis for the reinforcement design of similar bridges.

Reinforcement of reinforced concrete (RC) beams in-service have always been an important research field, anchoring steel plate in the bottom of the beams is a kind of common reinforcement methods. In actual engineering, the contribution of pavement layer to the bearing capacity of RC beams is often ignored, which underestimates the bearing capacity and stiffness of RC beams to a certain extent. The purpose of this paper is to study the effect of pavement layer on the RC beams before and after reinforcement.

First, static load experiments are carried out on three in-service RC hollow slab beams, meanwhile, nonlinear finite element models are built to study the bearing capacity of them. The nonlinear material and shear slip effect of studs are considered in the models. Second, the finite element models are verified, and the numerical simulation results are in good agreement with the experimental results. Last, the finite element models are adopted to carry out the research on the influence of different steel plate thicknesses on the flexural bearing capacity and ductility.

The experimental results showed that pavement layers increase the flexural capacity of hollow slab beams by 16.7%, and contribute to increasing stiffness. Ductility ratio of SPRCB3 and PRCB2 was 30% and 24% lower than that of RCB1, respectively. The results showed that when the steel plate thickness was 1 mm–6 mm, the bearing capacity of the hollow slab beam increased gradually from 2158.0 kN.m to 2656.6 kN.m. As the steel plate thickness continuously increased to 8 mm, the ultimate bearing capacity increased to 2681.0 kN.m. The increased thickness did not cause difference to the bearing capacity, because of concrete crushing at the upper edge.

In this paper, based on the experimental study, the bearing capacity of hollow beam strengthened by steel plate with different thickness is extrapolated by finite element simulation, and its influence on ductility is discussed. This method not only guarantees the accuracy of the bearing capacity evaluation, but also does not require a large number of samples, and has certain economy. The research results provide a basis for the reinforcement design of similar bridges.